CRF1000 Products on this page - quick links below

PC-8 Fuse Panel Kits  - 8 outputs, for power users 3 Circuit Solution - 3 outputs, for modest power needs Brake/Tail and Signal Adapters Turn Signal Adapters and Connectors Panel Mounting Push Rivets Accessory Power Adapters Electrical Connectors Installation page

PC-8 Fusepanel Kit (for power users)

Complete plug and play with all the wiring, a 40A relay, and a PC-8 fusepanel.

Read more about the PC-8 here.

This Kit is custom made for the new Africa Twin and is plug and play. Everything you need is included. Just strip your circuit wires and insert into the PC-8 outputs and tighten the screws. Both power and ground terminal blocks are built in. Please note that relay weather-proofing shown above is now an option on this Kit available in the options below.

Please Note - all CRF1000 PC8 and 3CS Kits now use the 6P connector found at far rear left under passenger seat. If your bike has a factory alarm system (or anything else plugged into this connector)  you will also need the Rear Acessory Splitter with this Kit.

To install this Kit you need to remove the left side tank side trim, and pull the battery out half way. Wires are easy to route to the battery and when you’re finished, everything will look built into the bike. You should be able to locate the PC-8 just about anywhere under the seat.

PC-8 with Relay Kit for CRF1000L $109.95 Connection Option Battery M6 Ring Terminals Powerlink Connector

It is convenient to mount the PC-8 with Dual Lock. You can buy some below.

Relay Kit Only for CRF1000L $49.95 Connection Option Battery M6 Ring Terminals Powerlink Connector

NEW! - The Powerlink Connection option is the same Kit with with short battery leads and a connector to plug into the Powerlink Battery Leads, making the overall total Kit the same length. We make special custom Powerlink Battery Leads for the CRF1000, buy below:

NOTE: The PL battery leads for the CRF1000 are custom length to fit perfectly.

PC-8 Kit Switching Connector for CRF1000

Please Note - all CRF1000 PC8 and 3CS Kits now use the 6P connector found at far rear left under passenger seat. Slice the tape to free the connector, then remove the cap. You can move it further forward to be accessible under the rider’s seat. Move it to a position shown by the finger below.

Installation page

Accessories:

Rear Accessory Splitter - for bikes with an alarm system (or anything else plugged into this connector) using the 6P connector under the passenger seat. This splitter allows normal hookup while providing hookup for our PC-8 or 3CS Kits. Rear Accessory Splitter $34.95

Dual Locks Strips - Two pairs of mating 3” (8 cm) Dual Lock strips. Great for many other projects too, this material has 5 times more holding strength than regular Velcro. Strips have excellent adhesive on the back. Clean surfaces with alcohol first.  2 Sets 3 Inch 3M Dual Lock Strips $2.95

Relay Splash Proofing Option:  A large sheath of removable shrinktube is shrunk over the relay connection to provide water proofing for those who like to cross rivers and get their bike wet. Relay Splash Proofing Option $2.95

3 Circuit Solution Sealed Kit (for modest power users)

Complete plug and play with all the wiring, a 20A relay, and a 3 circuit fusebox.

Read more about the 3CS here. See pics of it installed here. Note, all 3CS Sealed have been updated with new Furukawa modular fuseholders as shown below.

The 1 Fuse Unswitched version has a slightly different configuration.

This Kit uses all sealed connectors, (shown above even the relay is weather proofed). The relay switching and ground wires plug into the existing red connector under the seat. Three sealed connectors are included to install on your circuit wires, to plug into the Kit’s outputs.

This Kit is available in two versions:

‘all fuses switched’ version - all output circuits are switched on and off with the bike.

3 Circuit Solution for CRF1000L - All Fuses Switched  $56.95 Connection Option Battery M6 Ring Terminals Powerlink Connector Quantity:

‘1 fuse unswitched’ version - 2 output circuits are switched and one is always hot.

3 Circuit Solution for CRF1000L - One Fuse Unswitched  $58.95 Connection Option Battery M6 Ring Terminals Powerlink Connector Quantity:

NEW! - The Powerlink Connection option is the same Kit with with short battery leads and a connector to plug into the Powerlink Battery Leads, making the overall total Kit the same length. We make special custom Powerlink Battery Leads for the CRF1000, buy below:

NOTE: The PL battery leads for the CRF1000 are custom length to fit perfectly.

Extra Connectors:

2 Position .090 Waterproof MT Connector. Fits wires from .5mm - 1.25mm (22 - 16 AWG). Small size tough plastic housing with inner seal. Seals on each wire. Click below to buy: 2P090WP-MT Connector Set  $3.95 ea Quantity: Male Half $2.49 ea Quantity: Female Half $1.95 ea Quantity:

Crimper for sealed connector terminals:

The Hozan P-706 does a professional job on these types, go here to buy. This is a great tool for a home shop, most connectors on modern bikes are this type.

Please know that you don’t need a crimper to install these. You can pinch and solder if you know how to solder. I have a page about crimping and soldering here.

3CS Sealed  Leads and Extensions

Various pre-finished leads of the highest quality are available for running your circuit wires from the 3CS under the seat to up front to power a socket, SAE, aux lights, or other devices. Leads are available for a variety of power socket connections to plug in directly. Extensions can be used where you install the male connectors that come with the 3CS-S on the wires of your device (like an automotive socket with pigtails), everything then plugs together. Wires, connectors, and sheathing are high temp, highest quality, Japan made and assembled by Eastern Beaver.

3CS-S Extensions

- pre-made solutions to get from the 3CS Sealed to your accessory or splitter.

- 3CS Sealed male connector on one end and a female on the other end.

3CS-S Leads - these leads have specific terminating connectors for different accessories

3CS-S Leads with SAE Plug 2 Prong SAE Plug for battery chargers, etc., WITH 18 AWG wire. (NOW WITH SAE CAP) 3CS Leads Sealed (SAE) 80 cm (32”) $12.95 Quantity: 3CS Leads Sealed (SAE) 120 cm (48”) $14.95 Quantity: 3CS Leads Sealed (SAE) 160 cm (64”) $16.95 Quantity: 3CS-S Leads with T-Connector 2 Prong T-Connector for Powerlet and Hella type Socket - with 18 AWG wire 3CS Leads Sealed (TCON) 80 cm (32”) $12.95 Quantity: 3CS Leads Sealed (TCON) 120 cm (48”) $14.95 Quantity: 3CS Leads Sealed (TCON) 160 cm (64”) $16.95 Quantity: 3CS-S Leads with 1/4” Pushons 2 1/4” Sheathed Push-on Receptacles for Automotive Sockets etc. - with 18 AWG wire 3CS Leads Sealed (.250”) 80 cm (32”) $12.95 Quantity: 3CS Leads Sealed (.250”) 120 cm (48”) $14.95 Quantity: 3CS Leads Sealed (.250”) 160 cm (64”) $16.95 Quantity:

Lead Install Page

CRF1000L Rear Lighting Adapters

These bikes have a few connectors for rear lighting. One 3P sealed connector plugs directly into the tail light housing for the brake and tail lights. The other 2P connectors (3) are used for signals and licence plate light. Here are the new adapters that work on this model.

CRF1000L Brake/Tail Adapter - Brake/Tail Adapter Install and Help These adapters allow you to install aux brakelights, and aux tail lights without splicing into or changing the stock wiring and connectors. Version 1 - all wires are take-offs from stock wires. Red wire is brake, blue wire is tail, and black is ground. CRF1000L Brake/Tail Adapter V1 $24.95 Quantity: Version 2 - brakelight wire has input  (purple) and output (red) wires for BackOff type modulators. Tail light wire (blue) and ground (black) are take-offs from stock wires. CRF1000L Brake/Tail Adapter V2 $26.95 Quantity: Brake/Tail connector, far rear under passenger seat - connector plugs directly into light housing Signal connectors, rear right under passenger seat - orange and blue are signals, white is licence light CRF1000L Turn Signal Adapters - Signal Adapter Install and Help Available with blue or orange connector Available in two types: short 12 inches (30 cm) with female 4mm bullets, and 24 inches (61 cm) long with bare wires. Click below pics to buy. CRF1000L Signal Adapter Long $12.95 Connector Color Option Orange Connector Blue Connector Quantity: CRF1000L Signal Adapter Short $12.95 Connector Color Option Orange Connector Blue Connector Quantity: Signal light wire extensions with skyblue or orange connectors. CRF1000L Signal Wires Extension 16”(40cm) $12.95 Connector Color Option Orange Connector Blue Connector Quantity:

Turn Signal Splitters - with blue, orange, or white connectors. These units plug inline on the stock connectors give you two wire takeoffs for aux signals and other rear lighting devices requiring turn signal functions. White unit matches licence light connectors.

CRF1000L Turn Signal Splitter 24”(61cm) $14.95/ea Connector Color Option Orange Connectors Blue Connectors White Connectors Quantity:

Turn Signal Connectors

2 Position HC050 Connector Used for turn signal connectors on the CRF1000L Fits wires from .5mm - .75mm (22 - 18 AWG). Blue and Orange Available! 2P050-HC-Blue-Male  $1.79 ea Quantity: 2P050-HC-Blue-Female  $1.79 ea Quantity: 2P050-HC-Orange-Male  $1.79 ea Quantity: 2P050-HC-Orange-Female  $1.79 ea Quantity:

HE050 Male Terminal Fits wires from .75mm - 1.25mm (18 - 16 AWG). Click below to buy: M050-HE  $0.10 ea Quantity: HE050 Female Terminal Fits wires from .75mm - 1.25mm (18 - 16 AWG). Click below to buy: F050-HE  $0.10 ea Quantity:

Plastic Panel Mount Push Rivets

CF-1 -  $4.95 (pack of 10) Quantity:

 

Aux Power Connectors

Power Splitter for Front Fairing Power Connector

Duplicate of Honda’s splitter but better and tougher. See below for accessory connections. One output connector is fully wired (4P), the other has power and ground only (2P). You can use either output connector to power and ground GPS, Heated Grips, Power Socket, and more.

The accessory kit shown below has enough to fully wire both connectors, plugs are included for an unused connector. 2 Extra terminals are included. Further down this page you can buy all these components separately.

Sumitomo Sealed HM090

2 Position .090 Waterproof Connector. Fits wires from .5mm - 1.25mm (22 - 16 AWG). Tough plastic housing with inner seal, plus seals on each wire. Click below to buy: 2P090WP-HM Set $4.29 ea Quantity: Male Half $2.95 ea Quantity: Female Half $1.95 ea Quantity:

4 Position .090 Waterproof Connector. Fits wires from .5mm - 1.25mm (22 - 16 AWG). Tough plastic housing with inner seal, plus seals on each wire. Click below to buy: 4P090WP-HM Set $6.09 ea Quantity: Male Half $3.95 ea Quantity: Female Half $2.49 ea Quantity:

6 Position .090 Waterproof Connector. Fits wires from .5mm - 1.25mm (22 - 16 AWG). Tough plastic housing with inner seal, plus seals on each wire. Click below to buy: 6P090WP-HM Set $7.49 ea Quantity: Male Half $4.49 ea Quantity: Female Half $2.95 ea Quantity:

Sealed HM and MT Pins and Seals Terminals also fit HW sealed series. For HW seals see the DL series. Click below to buy: HM/MT/HW Male Terminal  $0.14/EA Quantity: HM/MT/HW Female Terminal  $0.14/EA Quantity: HM/MT Seal $0.09/EA Quantity: HM/MT Plug  $0.12/EA Quantity:

Fog Light Switch Connector - mates with the connector on the stock Honda foglight switch

2 Position Waterproof Female Connector (Center Rib). Fits wires from .5mm - 1.25mm (22 - 16 AWG). Tough plastic housing with inner seal, plus seals on each wire. Click below to buy: 2 Position 2P040WP-HX-CR-F $2.79 ea Quantity:

Also found on the CRF1000 - the 4P HX040 Sealed. Look here for this connector.

We stock most if not all of the connectors found on the bike, please browse our connectors pages.

go to top of this page