Yamaha’s XSR900 2016 -

• PC-8 Specifications and Features:
• - 4 threaded insert nuts provide case mounting and fuse panel installation mounting points
• - comes with an assortment of ATM fuses, one for each output circuit and a few extras
• - 8 hot + outputs (2 unswitched circuits, 6 switched circuits)
• - Switched circuits are turned off when the bike is shut down. An unswitched circuit is always hot - can be used for charging the battery
• - 8 ground outputs - much better to ground your auxiliary circuits here than on a bike’s frame
• - maximum fuse panel capacity 50 Amps (30A/20A - switched/unswitched)
• - maximum circuit capacity 20 Amps (15A continuous)
• - maximum output wire size 12 AWG (3 sqmm)
• - all hardware is stainless steel (except input posts which are tin plated steel)
• - black satin polycarbonate cover makes unit splash-proof yet allows it to breathe and stay cool
• - cover mounting tabs on each end can be broken off or left on, depending on mounting choice
• - simple robust design means no overheating and no problems with vibration
• - I designed this fuse panel with ease of mounting a priority. Therefore there are many mounting options: Dual Lock on back of case, fine threaded screws from back of panel, self tapping screws from inside through PCB inserts to panel, or nuts and screws on the case mounting ears at each end of the case.

PC-8 Fuse Panel Kit - 8 Circuits For Power Users

PC-8 Power Link Kit - 8 Circuit With Power Link Connection

4 Circuit Solution Sealed Kit for - for modest power users

Accessory Splitter - for low power users, splits the accessory port into two outputs

PC-8 Fuse Panel Kit

Complete plug and play kits, with all the wiring, a 40A relay, fuses, a PC-8 fusepanel, and more.

Battery Connect Complete Kit

Installation Note: This kit uses the accessory port at the front right of the bike ( near the radiator cap ). If you are already using that port for heated grips or such, you would need to purchase the splitter cable. The kit was designed so that the PC-8 & Relay sit under the seat. The battery cables run along the right side of the bike to the battery and the switched input lead runs under the tank to the OEM accessory port ( used for heated grips ) near the radiator cap.

OEM Accessory Connector

Picture courtesy of A. Johnson

PC-8 Power Link Kit - 8 Circuit With Power Link Connection

Complete plug and play kits, with all the wiring, a 40A relay, fuses, a PC-8 fuse-panel, and more.

With the PowerLink version, the PC-8 can be disconnected, temporarily, allowing jump starting or charging, protecting your accessories and allowing easy access to the battery. The PowerLink system allows one bike to give a boost to another bike, in the event of a flat battery, or it can be used to charge one bikes battery from another bike ( the bike doing the charging, should be running. Useful when a friends rectifier or generator has failed ). PowerLink accessory cables are sold separately here

XSR900 PC-8 PowerLink Kit ( Battery Connection is via the included PowerLink Connector )

Installation Note: This kit uses the accessory port at the front right of the bike ( near the radiator cap ). If you are already using that port for heated grips or such, you would need to purchase the splitter cable. The kit was designed so that the PC-8 & Relay sit under the seat. The battery cables run along the right side of the bike to the battery and the switched input lead runs under the tank to the OEM accessory port ( used for heated grips ) near the radiator cap.

4 Circuit Solution Sealed Kit

This Kit is for medium power needs up to 35A total current on the Kit.

This Kit has two main fuseholders. The black is for the switched circuits which also each have a separate fuseholder, the main white fuseholder is for the unswitched circuit. You can charge the battery through the unswitched circuit which is always hot. The switched circuits are switched by the relay to be on only when the bike is on.

This Kit uses Sumitomo MT sealed .090 connectors that are easy to work with if crimping or soldering. See here for a crimper  for these that will do a professional job on these. The  Hozan P-706 is my recommended crimper for sealed types.

Three switched outputs are provided, controlled by a 20A relay and a main fuseholder of 20A max. Switched outputs are max 12A each. These switched outputs are great for most of your accessories, cellphone, GPS etc, even heated clothing can be powered.

One unswitched output is provided direct from battery using its own fuseholder, with max capacity of 15A. The bike battery can be charged with this circuit. This higher power circuit can also power an air compressor or power heated clothing. Or you can use this circuit for a GPS which will stay on and powered when you shut off the bike.

The relay is a very compact 20A unit with extra protection shrunk over it. Mating connectors and fuses are included. Also, an extra terminal and seal is included, as well as cable ties. Extra connectors and parts are available on  the Accessories Page. Two Positaps are included for the relay switching wire and ground.

Leads, extensions, and splitters to plug into the 3CS Sealed are now available on  the Accessories Page.

Kit with Battery Connections  (also available to hookup to our Powerlink battery leads)

Generic 4CS Image

Installation Note: This kit uses the accessory port at the front right of the bike ( near the radiator cap ). If you are already using that port for heated grips or such, you would need to purchase the splitter cable. The kit was designed so that the PC-8 & Relay sit under the seat. The battery cables run along the right side of the bike to the battery and the switched input lead runs under the tank to the OEM accessory port ( used for heated grips ) near the radiator cap.

Accessory Splitter
This cable converts your front OEM accessory port into two outputs. So you can run heated grips & also connect an accessory fuse box such as the PC-8.

Accessories:

Dual Locks Strips - Two pairs of mating 4” (10 cm) Dual Lock strips. Great for many other projects too, this material has 5 times more holding strength than regular Velcro. Strips have excellent adhesive on the back. Clean surfaces with alcohol first.  2 Sets 4 Inch 3M Dual Lock Strips $2.95 Quantity:

More PC-8 mounting accessories click here.